< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=2272319103321359&ev=PageView&noscript=1" />
New Customer Offer: 10% Off — Coupon code: FIRST10

No products in the cart.

Rear Fog Lamps: UN R38 Approval, R48 Installation, and Workshop Checks

A component approval mark does not prove that a rear fog lamp is correctly installed on a vehicle. UN Regulation No. 38 addresses the lamp as a device, while UN Regulation No. 48 adds vehicle-level requirements for number, position, visibility, switching, and a tell-tale.

The practical sequence for rear fog lamp installation is to confirm the applicable component route, identify the vehicle’s approval requirements, measure the installed lamp, and test its circuit. The rules vary by vehicle category, approval series, market, and date, so this guide uses UNECE R38 Revision 4 and R48 Revision 13 as dated reference texts rather than a claim about every current national rule.

Quick answer

Rear fog lamps are a useful case study in the difference between part approval and installation approval. R38 Rev.4 defines the device as a lamp that makes a vehicle more visible from behind by emitting a red signal of greater intensity than rear position lamps. R48 Rev.13 refers to rear fog lamps approved under R38 or R148, then specifies how the device is fitted to vehicles covered by that text. Passing the component test does not automatically satisfy the vehicle installation rules.

Under the cited R48 revision, one or two rear fog lamps are allowed. A single lamp may be placed opposite the prescribed traffic side or centered; the normal height range is 250–1,000 mm, with specified cases that can extend to 1,200 mm. The same text specifies visibility angles, electrical logic, a non-flashing tell-tale, and a gap greater than 100 mm from each stop lamp. The specific vehicle approval and applicable amendment series still control.

QuestionComponent-level answerVehicle-level answer
Which document?R38 or, where referenced, R148R48 installation text
What is being checked?Lamp design, approval evidence, markingNumber, location, visibility, circuits, tell-tale
Does an E mark settle installation?NoCheck vehicle-level rules and actual fitment
Which legal text applies?Approval series and jurisdictionVehicle category, approval date, and local rules
A diagram separating device approval from vehicle installation requirements
The lamp and the vehicle installation answer different approval questions.

Approval and installation answer different questions

The word “approved” is incomplete unless it identifies what was approved and under which legal instrument. UN Regulation No. 38 Rev.4 is a component regulation. Its text contains a scope, lamp definition, technical specifications, intensity and colour requirements, tests, and markings. This is the first document to check for rear fog lamp installation evidence. The text says an approval is granted when samples of a lamp type meet its requirements, and it describes an international approval mark that identifies a country and approval number with the relevant rear fog category symbol.

UN Regulation No. 48 Rev.13 text (GAR page with UNECE download and mirror) is a vehicle installation regulation. In section 6.11, it explicitly names UN Regulation No. 38 or 148 and describes installation requirements. This separates rear fog lamp installation from approval of the component. That cross-reference means component approval is one part of a larger conformity chain. A correctly marked lamp can still be mounted at the wrong height, be blocked from required viewing angles, sit too close to a stop lamp, or have an incompatible switching circuit.

This distinction is familiar in other vehicle-lighting decisions. SAEC’s published DOT versus E-mark guide explains what an approval mark can and cannot prove. Its FMVSS 108 turn-signal guide is about a different lamp function, but it provides a useful comparison: identify the function and governing text before treating a marking as a full-vehicle compliance statement.

StageQuestion to answerEvidence to retain
DeviceIs this lamp type approved for the intended rear-fog function?Marking, approval number, supplier documentation
VehicleDoes the installation meet the applicable layout and circuit requirements?Drawing, measurements, wiring diagram, vehicle category
UseWhen may the driver legally operate it?Local road rules and weather guidance

What UN R38 Revision 4 covers

The UNECE R38 Rev.4 document applies to rear fog lamps for listed vehicle categories: L3, L4, L5, L7, M, N, O, and T. It defines a rear fog lamp by its purpose and red output relative to rear position lamps. The text then sets component-level requirements that include optical characteristics, light-source information, intensity, colour, testing, and approval marking. This is why a red lens by itself cannot establish that a device qualifies as an approved rear fog lamp.

The revision’s marking provisions are more specific than a generic “E-marked” label. R38 Rev.4 describes an international approval mark containing an E in a circle, the distinguishing number for the approval country, and an approval number. It also uses an additional symbol for steady or variable luminous intensity. The exact mark interpretation depends on the lamp and approval series. An installer should compare the physical marking with the part’s approval information rather than guess from a small moulded symbol.

R38 Rev.4 also sets photometric limits and colour. In the opened text, steady-intensity F/F1 devices have a maximum intensity of 300 cd in the specified observable directions; variable-intensity F2 devices have a different maximum. The source text states that the light within the defined distribution field must be red. These are revision-specific details and should not be repeated as timeless or universal figures. This article does not replace the full regulation, type-approval file, or current national implementation.

A practical buyer or technician can record the manufacturer, lamp part number, device category, approval number, light-source configuration, and relevant revision. A Wikimedia Commons photo of a Ford Focus Mk I rear fog lamp illustrates a real installed unit; the photo is not an approval document. If markings are hidden after fitment, take a pre-installation photo and retain the documentation. Do not file, paint, or cover required markings to make an aftermarket installation look cleaner. If the lamp has been repaired or assembled from mixed components, verify that its approved identity remains valid.

What UN R48 Revision 13 adds

R48 Rev.13 places rear fog lamps under section 6.11 and explicitly references R38 or R148. It identifies F, F1, or F2 category devices as mandatory for the device classes listed in its presence paragraph, allows one or two lamps, and sets position and circuit conditions. The exact scope depends on the regulation’s vehicle category and approval context. Readers should not treat one paragraph as a universal rule for every road vehicle worldwide.

The installation provisions include more than geometric measurements. The rear fog lamps must not be switchable on unless main-beam headlamps, dipped-beam headlamps, or front fog lamps are on. They must be capable of being switched off independently of other lamps. The text allows either a state-retention arrangement until position lamps are turned off, with a requirement to remain off until deliberately reactivated, or an additional audible warning under a specified ignition/key/door condition while the rear-fog control remains on.

The same section requires a circuit-closed tell-tale described as an independent, non-flashing warning light. A separate Proton Persona rear fog-lamp photo shows a real lamp detail, but photographic appearance alone cannot verify rear fog lamp installation compliance. It also requires a distance greater than 100 mm between each rear fog lamp and each stop lamp. The allowed switching logic contains a trailer exception: the towing vehicle’s rear fog lamp may switch off automatically when a connected trailer’s rear fog lamp is on. That is a specific permitted behavior, not a general excuse for a lamp that drops out under unrelated conditions.

R48 Rev.13 itemText in section 6.11Workshop evidence
NumberOne or twoCount the approved devices
Single-lamp widthOpposite prescribed traffic side or centeredMeasure from vehicle median plane and identify traffic side
Vertical positionNormally 250–1,000 mmMeasure the reference point above ground
Stop-lamp spacingGreater than 100 mm from eachMeasure nearest edge/reference as required by applicable method
Tell-taleIndependent, non-flashing, circuit-closedObserve in the intended operating state

How many lamps and which side may be used

R48 Rev.13 permits one or two rear fog lamps. If only one is fitted, the text says it should be on the side opposite the direction of traffic prescribed in the country of registration, or its centre of reference may be on the vehicle’s median longitudinal plane. This rule is often simplified as “one lamp on the driver’s side” or “one lamp on the right,” but those statements can fail when the vehicle is registered in a different market or the traffic convention changes.

The safest procedure is to start with the vehicle’s country of registration and the applicable approval text, then mark the longitudinal centre line of the vehicle. Determine whether the installed single lamp is centered or on the prescribed opposite side. Do not use a tail-lamp lens outline or bumper edge as a substitute for the regulation’s reference point. A lamp that appears close to the middle may still be off-center enough that the measurement method matters.

Two lamps avoid the single-lamp side decision but do not automatically resolve every placement issue. Each device still has to meet the applicable photometric, position, visibility, electrical, and separation requirements. If both are integrated into a rear combination lamp, the device symbols and approval information should identify the functions present. A clear-looking lens assembly is not enough to prove that the rear fog function is approved or correctly connected. Rear fog lamp installation must be checked against the right revision and the vehicle’s actual dimensions.

The categories and dates matter. R48 can apply in different series and amendment levels, and the vehicle type approval may have been granted under a different applicable text. Preserve the approval certificate or homologation information when available. In a retrofit on an older vehicle, check whether the local rules require one lamp, what position is permitted, and whether a modification is allowed. Do not copy the placement from a modern vehicle in another jurisdiction as a universal template.

Height, visibility, and rearward orientation

In R48 Rev.13, the normal vertical range places the rear fog lamp no lower than 250 mm and no higher than 1,000 mm above the ground. The document allows the maximum to rise to 1,200 mm for lamps grouped with any rear lamp or for N3G off-road vehicles. These are precise exceptions; they should not be shortened into “all trucks can mount it higher” or applied to a vehicle that is not within the specified condition.

R48’s geometric visibility requirement for the rear fog lamp is 5° upward and 5° downward, plus 25° to the right and left. Its orientation is rearwards. These angles define a region from which the lamp needs to be visible; they do not mean a technician should aim the lamp like a headlamp or use the numbers as a substitute for component photometry. Bodywork, spare tires, tow accessories, tailgate-mounted equipment, and a trailer coupling can obscure part of the required field.

Measure from the required reference point and reference axis using the method set by the regulation and the vehicle’s approval documentation. Record the ground condition and vehicle state, because ride height and load can change the measured relationship to ground. The original text allows category- or grouping-specific treatment, so a generic bumper-to-lens estimate is useful only as a screening check, not a final compliance result.

Rear-view layout showing centerline, stop lamps, and example single rear fog lamp position
This schematic is illustrative; use the vehicle’s applicable approval method for measurements.
Geometry checkR48 Rev.13 referencePractical caution
Height250–1,000 mm; specified exceptions to 1,200 mmConfirm exception applicability before using the upper limit
Vertical visibility5° up and 5° downCheck obstructions, including vehicle accessories
Horizontal visibility25° right and 25° leftVerify from the reference point, not a casual rear view
OrientationRearwardsAvoid mounting a lamp that points sideways or down

Why stop-lamp separation matters

R48 Rev.13 requires the distance between each rear fog lamp and each stop lamp to be greater than 100 mm. The purpose of the check is to maintain separation between two red functions with different signals: the rear fog lamp is a high-intensity red warning in poor visibility, while the stop lamp indicates braking. If the lamp faces sit too close together, observers can have more difficulty distinguishing the functions, especially when the rear fog is illuminated.

Do not assume a wide gap between lamp housings proves the required distance. The applicable definition may use reference points or apparent surfaces, not the outer edge of a decorative bezel. Measure the installed devices according to the regulation and the approval information. If the rear fog is integrated into a combination lamp, use the approved layout rather than measuring an arbitrary seam in the plastic.

Spacing also interacts with aftermarket body parts. A custom bumper, replacement tail lamp, towbar, or added light panel can move the apparent position of one function without changing the vehicle’s original approval drawing. If the vehicle has been modified, compare the actual arrangement with the applicable documentation and local rules. A measurement just at the stated number does not satisfy a requirement written as “greater than” that number; allow margin for measurement uncertainty and fitment variation.

When a lamp is too close, do not solve the problem by masking part of its lens or changing a stop-lamp bulb. Repositioning may affect visibility angles, height, wiring length, and rearward orientation. A qualified vehicle-lighting engineer or approval specialist should assess a non-standard installation, especially where the change affects a vehicle subject to type approval or inspection.

Electrical switching is part of compliance

R48 Rev.13’s circuit requirements describe allowed interactions, not a specific universal wiring diagram. The rear fog lamp must not turn on unless main beam, dipped beam, or front fog lamps are on, and the driver must be able to switch it off independently of other lamps. This does not mean the lamp should always go out when high beam is selected, nor does it mean any convenient ignition-switched feed is acceptable.

The text then describes two alternative ways to manage the lamp state after the driver leaves the vehicle. In one, the lamp can remain on until the position lamps are switched off, after which it must stay off until intentionally switched on again. In the other, if the ignition is switched off or the key removed and the driver’s door opened while the control is on, an additional warning at least audible is given. Read the exact paragraph before selecting a relay or controller; a retrofit installer should document which allowed approach the vehicle uses.

A common workshop failure is an accessory relay wired to a power source that ignores the expected enabling lamps. Another is an indicator or trailer circuit sharing a ground that causes flicker or backfeed. The regulation allows a specific towing-vehicle behavior when a connected trailer’s rear fog lamp is on; diagnose the vehicle and trailer socket as a system before assuming a fault. The vehicle’s approved wiring diagram and the trailer interface can affect the expected result.

SAEC’s published LED warning-light guide discusses other warning-light systems, but a beacon or light bar must not be wired as a rear fog lamp simply because both are red and visible. See also the LED Warning Lights category and Off-Road LED Light Bars category for separate product families; their category placement does not establish rear-fog approval.

The tell-tale is not optional in the cited R48 text

R48 Rev.13 specifies an independent, non-flashing circuit-closed tell-tale for the rear fog lamp. “Circuit-closed” means the indicator reports the lamp circuit’s commanded operating state; it should not be confused with a generic illumination icon that comes on whenever the switch is touched. The regulation’s wording is an operational requirement, so a retrofit must account for the indicator, not just the rear lamp output.

The dashboard symbol and color can be checked against the vehicle’s documentation and the applicable market requirements. R48 Rev.13’s clause quoted here defines the tell-tale behavior; it does not make this article a complete dashboard-symbol guide. Do not assume the rear fog icon is interchangeable with a front fog symbol. A switch panel may use icons that look similar, especially after a prior owner has replaced the instrument cluster or added a non-factory switch.

Test the tell-tale with the lamp in the valid on condition and then check it turns off when the rear fog lamp is switched off. If the vehicle has a diagnostic system, read its wiring diagram or diagnostic procedure before probing an electronic module. An LED retrofit can draw less current than the original bulb and affect a monitoring circuit; use the lamp manufacturer’s and vehicle maker’s approved components rather than adding an undocumented resistor that could heat nearby trim.

The tell-tale also supports correct use: the driver can see when the rear fog lamp remains on after visibility improves. However, the indicator itself does not tell the driver whether the lamp is legally appropriate for the weather. That question belongs to local road-use guidance and safe-driving practice.

How to read the approval mark without overclaiming

An R38 Rev.4 approval mark includes the international E mark, a country distinguishing number, an approval number, and an F symbol with a figure indicating the specified steady or variable luminous intensity category. The lamp must carry the approval markings in the manner described by the regulation. A lens can carry several symbols because a combined lamp may perform more than one approved function; the correct function symbols and associated approval information need to be legible after installation.

A mark can be misread when it is partly hidden, worn, or molded into a surface that is hard to photograph. Clean the lens gently, use angled light, and photograph the full marking before installation. Compare it with the supplier’s approval document. If the serial or part number does not match, ask the supplier or approval holder for confirmation. A copied-looking marking on an online listing is not verification of the specific device delivered.

An E mark alone is also not a universal road-use permit. It identifies approval under a UN regulation within the agreement’s framework; the vehicle country’s rules, the applicable approval series, and the rest of the installation still matter. The current R48 document itself points to either R38 or R148 for the rear fog component, so an R148-approved device may be the appropriate route for a specific newer application. Verify against the exact text and approval file; do not infer that all R38 marks are invalid or that every R148 device is interchangeable.

Keep a photo of the device marking, the installation measurements, and the vehicle approval reference together in the service record. This creates a traceable package for inspection or later repair, particularly when a lamp has been integrated into a combination unit or a bumper has been replaced.

A repeatable workshop inspection sequence

A useful inspection of rear fog lamp installation starts with identity and scope. Record the vehicle category, registration jurisdiction, first-use or type-approval date where relevant, and any modifications to the rear body. Locate the original equipment or approval documentation, then identify the rear fog-lamp part and its approval route. If these details are uncertain, stop before treating a generic online diagram as a legal specification.

With the vehicle on level ground in the defined test condition, record the number of rear fog lamps, the centerline, the reference point, the height, the distance to each stop lamp, and any obstructions. Measure the angular visibility field using an appropriate method when required. A helper can stand at safe viewing positions to check obvious masking, but that is not a substitute for formal measurement where the approval process calls for it. Photograph the setup so another technician can reproduce the readings.

Next inspect the lens, housing, fasteners, connector, wire routing, earth connection, and seals. Check for water, corrosion, loose brackets, paint or tape covering an optical surface, and repairs that compromise security or light output. Operate the lamp with the correct enabling lamps, confirm independent off control, test the tell-tale, then cycle the other relevant lamps and trailer connection according to the vehicle’s wiring instructions. Do not deliberately create shorts or load an electronic output with an unapproved test lamp.

Finish by documenting pass, fail, or “not confirmed” for each item rather than writing one vague note. List the exact regulation revision used, measurement method, equipment, vehicle state, and any assumptions. If the lamp or bodywork is non-standard, refer the case to a type-approval or vehicle-lighting specialist instead of silently adapting the measurements.

Inspection stepRecordEscalate when
Vehicle scopeCategory, jurisdiction, approval date if knownRequired text or category is unclear
ComponentMarking, part number, approval routeMarking is missing, illegible, or inconsistent
PositionCount, side/center, height, visibility, separationAny measurement conflicts with applicable text
CircuitEnabling conditions, independent off, state logicBackfeed, flicker, unexpected state retention
IndicationNon-flashing tell-tale operationTell-tale is absent or does not track the lamp

What the UK MOT example does and does not prove

The UK Driver and Vehicle Standards Agency (DVSA) MOT inspection manual is a useful national example because it shows how a roadworthiness inspection turns lamp rules into checks. It offers a local inspection view of rear fog lamp installation. Its current online section says the one rear fog lamp required on vehicles first used on or after 1 April 1980 must be at the centre or offside. It requires a steady red light, a secure and operable switch accessible from the normal driving position, and a check that other lamps do not adversely affect rear-fog operation. It also requires a tell-tale where the rear fog lamp is mandatory.

The manual allows a rear fog lamp to extinguish when main beam is switched on or when dipped beam is switched off. This differs in wording and purpose from the R48 Rev.13 type-approval logic described earlier. An MOT test manual is not a substitute for the vehicle’s original type-approval document, nor should its UK inspection rules be generalized to another country. It answers an in-service inspection question for its stated jurisdiction and vehicle conditions.

This distinction is practical for imported and modified cars. A vehicle may have been type-approved under one framework and later inspected under another national regime. The workshop should identify both the relevant approval conditions and the current inspection rule rather than declaring a configuration legal solely because it passes one test. Where a country’s rules are unclear, consult the national authority, approved inspection body, or qualified type-approval specialist.

The DVSA page is also useful for fault diagnosis because it lists switch operation, position, colour, tell-tale, and interaction with other lamps separately. Those checks make a better work order than “rear fog works.” A technician can report a steady red output and a working switch while separately flagging that original approval documents were not available.

Using rear fog lamps responsibly in poor visibility

A compliant installation is not an instruction to use the lamp in all rain, darkness, or mist. Operational guidance is jurisdiction-specific and depends on visibility and other road conditions. The UK Met Office severe-weather page, pointing readers to the Highway Code, says headlamps should be used when visibility is seriously reduced, generally when the driver cannot see more than 100 metres, and advises drivers to know how their front and rear fog lamps operate. That is UK-facing guidance, not a universal threshold for every jurisdiction.

Rear fog lamps are intense relative to rear position lamps by design. When used in clear conditions or close behind another vehicle, the bright signal can distract or dazzle following drivers and make brake-lamp changes harder to distinguish. Drivers should switch them off when visibility improves, follow local law, and retain enough distance for stopping. Automatic switching logic and a tell-tale help, but the driver remains responsible for the choice.

Before setting out in fog, learn the switch sequence while parked, check that the tell-tale responds correctly, and confirm the lamp is not accidentally left on. If the switch is unfamiliar, consult the vehicle handbook. If a lamp is damaged or flickers, do not assume that the other rear lamps provide the same visibility function. Repair the fault and avoid driving in severe low visibility until the vehicle can be seen as required by local rules.

Close-up of a rear fog lamp lens on a Ford Focus Mk I
Photograph by Frettie; this image shows a real rear lamp lens, not its approval marking.

These operational points should not be mixed into component approval. R38 and R48 technical approval and installation rules answer design and fitment questions; a road code or weather authority explains when the driver should use the lamp. All three layers matter, but each has a different scope.

Common retrofit and service errors

A frequent error is choosing a red lamp based only on appearance. A decorative red lens, a brake lamp, a rear position lamp, and a rear fog lamp are distinct functions. Confirm the device’s approval and the intended circuit before wiring it in. Another mistake is treating a component mark as proof that height, side, visibility, and spacing are correct on the finished vehicle.

A second error is copying a wiring diagram from a different vehicle. The R48 Rev.13 text permits defined circuit behaviors and contains a trailer exception, but it does not specify one universal relay layout for every vehicle. A retrofit that works on a simple incandescent circuit can behave differently with a body-control module, lamp monitoring, towing module, or LED replacement. Use the actual vehicle wiring information and approved interface components.

Installers also sometimes rely on an illuminated dashboard symbol without confirming the lamp output, or they test the rear lamp but ignore the tell-tale. Both ends of the circuit need to be checked. A wrong earth can cause dim output, backfeed, or interaction with turn and stop lamps. When this happens, inspect the earth path and connector for corrosion before replacing the lamp assembly. Do not mask an optical problem with a higher-output bulb; that can make glare worse and may invalidate the component approval.

Finally, do not use the UK MOT inspection manual as a global installation rule. It is an authoritative UK source and an excellent local example, but its date cutoffs, position wording, and permitted switching behaviors do not automatically transfer to other jurisdictions. State the source’s boundaries whenever using it in advice.

Frequently asked questions

No. It can support component approval under the identified regulation and approval series. Vehicle-level position, visibility, spacing, wiring, tell-tale, and jurisdiction rules still need to be checked.

Can one rear fog lamp be mounted in the center?

R48 Rev.13 says a single lamp may be on the side opposite the prescribed traffic direction or may have its centre of reference on the vehicle’s median longitudinal plane. Confirm that this revision and its conditions apply to the specific vehicle.

Is 1,200 mm the maximum height for every vehicle?

No. The normal maximum in the cited R48 revision is 1,000 mm. The text provides an increase to 1,200 mm for rear fog lamps grouped with any rear lamp or for N3G off-road vehicles. Check the exact applicability before using an exception.

Must a rear fog lamp switch off with the headlamps?

R48 Rev.13 says it cannot be switched on unless main beam, dipped beam, or front fog lamps are on, and it must be switchable off independently. The detailed permitted state logic should be read in the applicable version. UK MOT instructions describe some permitted extinguishing behaviors for inspection; that is a UK-specific example.

When should a driver use a rear fog lamp?

Follow the road rules in the vehicle’s jurisdiction and turn the lamp off when visibility improves. The UK Met Office and Highway Code guidance is one jurisdiction-specific example, not global legal advice.

Editorial note

SAEC Lighting Engineering Team, Foshan Last updated: 2026-11-03

Sources

  • UN Regulation No. 38, Revision 4 — UNECE: https://unece.org/sites/default/files/2022-09/R038r4e%20%282%29.pdf
  • UN Regulation No. 48, Revision 13 — UNECE document; GAR page with download and mirror
  • MOT inspection manual: 4. Lamps, reflectors and electrical equipment — UK DVSA: https://www.gov.uk/guidance/mot-inspection-manual-for-private-passenger-and-light-commercial-vehicles/4-lamps-reflectors-and-electrical-equipment
  • Driving in severe weather — Met Office: https://weather.metoffice.gov.uk/warnings-and-advice/seasonal-advice/travel/driving-in-severe-weather
  • Rear fog light of Ford Focus Mk I — Wikimedia Commons: https://commons.wikimedia.org/wiki/File:Rear_fog_light_of_Ford_Focus_Mk_I.jpg
  • 2019 Proton Persona Executive CVT (40) — Wikimedia Commons: https://commons.wikimedia.org/wiki/File:2019_Proton_Persona_Executive_CVT_%2840%29.jpg
  • FMVSS 108 Turn Signal, Brake and Clearance Lamp Rules — SAEC: https://saec-lights.com/standards-safety/fmvss-108-turn-signal-requirements/
  • Are LED Light Bars Street Legal? — SAEC: https://saec-lights.com/standards-safety/are-led-light-bars-street-legal/
  • LED Warning Lights and Beacons: What R65, J845 and Class Ratings Really Buy You — SAEC: https://saec-lights.com/buying-guides/led-warning-light-beacon-buying-guide-r65-j845/
  • LED Warning Lights category — SAEC: https://saec-lights.com/product-category/industrial/led-warning-lights/
  • Off-Road LED Light Bars category — SAEC: https://saec-lights.com/product-category/off-road-lights/led-light-bars/